Talk About Network

Google


Register and Login
Nick
Password
Register create new account Sign up is FREE and you can post replies, new topics, bookmark posts and more!
Recover lost password


Cycling > Technical aspects > Re: Cone bearin...
Latest [ Topics | Posts ] Archive Post A New Topic Post a Reply
<< Topic < Post Post 2 of 8 Topic 16048 of 17218
Post > Topic >>

Re: Cone bearings

by A Muzi <am@[EMAIL PROTECTED] > May 5, 2008 at 02:56 PM

shazzbat wrote:
> I recently acquired a ****mano mountain bike. I've replaced the bottom 
> bracket and it's bearings and now turned my attention to the rear wheel 
> which had a lot of play in it. It's a 26" wheel and has a set of 6
sprockets 
> attached. Removing the spindle, I found it to be deeply scored and the
cone 
> on the sprocket side badly mangled. Getting a new spindle and cones
isn't a 
> problem, but it seems to me there's probably something missing from the 
> set-up, as there's a big gap between the cone and the housing, so even
when 
> I refit the spindle, cone and bearing balls, it's not going to take up
the 
> play. When I took it apart, the balls were around the outside with
enough 
> room for the cone to pass right through. Is there somewhere I could
check 
> out a diagram online to see what's missing?
> 
> And how is the group of sprockets removed? Not that I need to right now,
but 
> I'd like to know for future reference.

Most probably a freewheel hub, although possibly a cassette system. 
Either would have a cracked or eroded right side dust cap if it was 
ridden much with a bearing problem.

Freewheels remove with a tool which holds the inner body and are 
specific to the freewheel model. Cassettes of that era disassemble by 
unscrewing the small gear. Either a more thorough description or a 
consultation with a competent LBS would be helpful.

Do clean and inspect the cup inside the hub before going much farther. 
If it was ridden loose for a while you may have damage there, the 
bearing diameter being much larger after the cup erodes or cracks. I 
couldn't tell from your description if it was a bearing cup problem or a 
missing dust seal.

traditional threaded hubs look like this:
http://www.yellowjersey.org/photosfromthepast/MAILLARD.JPG
The freewheel removes completely

cassettes something like this:
http://www.yellowjersey.org/photosfromthepast/CANEWHUB.JPG
or
http://bernd.sluka.de/Fahrrad/****mano/TM/FH-RM40-7QR_1995.gif

the ratchet assembly is part of the hub, the sprockets slide off.
-- 
Andrew Muzi
  <www.yellowjersey.org/>
  Open every day since 1 April, 1971
** Posted from http://www.teranews.com
**
 




 8 Posts in Topic:
Cone bearings
"shazzbat" <  2008-05-05 20:24:21 
Re: Cone bearings
A Muzi <am@[EMAIL PROT  2008-05-05 14:56:29 
Re: Cone bearings
"shazzbat" <  2008-05-05 23:34:23 
Re: Cone bearings
"shazzbat" <  2008-05-06 09:45:15 
Re: Cone bearings
M-gineering <ikmotgeen  2008-05-06 11:02:32 
Re: Cone bearings
A Muzi <am@[EMAIL PROT  2008-05-06 14:10:06 
Re: Cone bearings
"shazzbat" <  2008-05-07 19:30:40 
Re: Cone bearings
A Muzi <am@[EMAIL PROT  2008-05-07 13:54:32 

Post A Reply:
  Go here to Signup

AddThis Feed Button


About - Advertising - Contact - Frequently Asked Questions - Privacy Policy - Terms of Use - Signup

Contact
tan12V112 Sat Aug 30 5:07:35 CDT 2008.